⚓ Keel

← Back to diagram

#7

M24 Replace? 2/5

Nautor comment

Nothing to do but check the thickness of plate + rolling residue.

Bolt dimensions

D2 — Total bolt height
68.81 mm
D1 — Lead to thread
19.5 mm
H1 — Hull hole depth
51.77 mm
H2 — Keelson to plate
32.08 mm
Plate thickness (calc.)
19.69 mm
Keel width at station
14.5 in

D2 is the bolt's total height, from the head/tip down to the top of the lead. D1 is the height from the lead up to where the threads start. H1 is how deep the hole in the hull is where the bolt sits. H2 is the thickness from the bottom of the keelson to the bottom of the internal plate. Plate thickness is calculated as H1 minus H2. Keel width is measured across the bolt centers at this bolt's station.

Backing plate

Two-hole plate, shared with #6
Height (fore/aft)
80 mm
Width (athwartships)
174.75 mm (6.88 in)
Depth (thickness)
8 mm
Hole diameter
30 mm
Condition
Flat

Proposed extension — profile cutaway · v2 (Nov 12, 2026)

To scale, section through the bolt centreline. Heights in mm above the lead keel baseline. The fiberglass measures 39 mm, but the keel and hull faces aren't flush and leave an air gap of about 6–7 mm that won't close, so the backing plate top sits at about 54 as mounted.

Before — #7 as it stands

54 as mounted 68.8 tip (D2) 14.8 in nut #7: Only 14.8 of 18 mm in the nut M24 nut (18) 8 mm backing plate Fiberglass (39) Air gap ~7 Lead keel (baseline 0)

After — with extension · v2 (Nov 12, 2026)

M24 extension v2 (Nov 12, 2026) 8 excavation 37 shoulder 47 stud 54 as mounted 84 tip 92 total 30mm (10 threads) 3 2 18 Ø44 body 63 plate 75.7 excavation (63 + ½″) Full nut engagement, 12 proud Fiberglass hole enlarged to Ø46 up to ~38 only — stays clear of the backing plate Extension: Ø44 body, M24 female thread Existing M24 bolt, cut to 33 above excavation floor Tack weld (316 stainless filler) 63×63×6 plate, Ø44.3 hole, top flush with keel Lead keel (baseline 0)

Extension: XM-19 HS, ASTM A479 — MTR required; weld plate 316 stainless, tack welded with 316 stainless filler. M24 nut, 18 mm, seated on the backing plate with no washer (drawn across corners). The original bolt's thread starts at D1. Excavation 75.7 mm square (63 + ½″, the original plate's pocket widened chiselling it out), round the 63 mm plate. Assumed: the fiberglass hole is enlarged to Ø46 (about 1 mm clearance on the Ø44 body).

Strength vs. the A4-70 rod

Rod (M24, A4-70, As 353 mm²): yields at 159 kN, breaks at 247 kN. Each cell is yield / break in kN, with % of the rod's. The stud is the same thread as the rod, so the bar needs at least Rp0.2 450 MPa and Rm 700 MPa.

Section 316 annealed (ASTM A479) 205/515 MPa · weaker than the rod XM-19 annealed (Nitronic 50 / Aquamet 22, A479) 380/690 MPa · weaker than the rod XM-19 high strength (Nitronic 50 HS / Aquamet 22HS) 725/930 MPa · as strong as the rod
Body round the internal thread 219 (138%) / 550 (223%) 406 (256%) / 737 (299%) 774 (488%) / 993 (403%)
Shoulder (narrowest) 93 (58%) / 233 (94%) 172 (108%) / 312 (127%) 328 (207%) / 421 (171%)
Stud neck (plain, Ø24) 93 (58%) / 233 (94%) 172 (108%) / 312 (127%) 328 (207%) / 421 (171%)
Stud thread 72 (46%) / 182 (74%) 134 (84%) / 243 (99%) 256 (161%) / 328 (133%)
Internal thread stripping — / 505 (205%) — / 677 (274%) — / 912 (370%)
Stud thread stripping in the nut — / 223 (90%) — / 299 (121%) — / 403 (163%)

Bold: the weakest section. The shoulder's tightest fillet radius is 2.1 mm (Kt ≈ 2.0); on the larger unthreaded section that peaks at about 1.6× the thread's nominal stress, below a cut thread root's (Kt about 3–4), so the transition isn't the weak point. The stud thread stops at a 3 mm plain neck at Ø24 and washes out (no undercut); full thread from 44.5 above the keel. Spec minimums, not measured values; thread stripping at 0.6 Rm.

Open print sheet CAD (DXF, M24): extension · weld plate

Machine-shop upload set (M24, qty 2)

Extension: STEP · IGES · STL · Drawing (PDF) · FreeCAD · STEP, threaded · STL, threaded

Weld plate: Cut DXF · STEP · IGES · STL · Drawing (PDF)

Loading 3D model…

Couldn't load the 3D model.

Finished part, threads modelled · drag to rotate

Proof Test / Fixture

Starting proof-test stack — a calculated starting point, not an approved dimension. H1 is remeasured in the field before every test.

Baseline H1
51.77 mm
Calculated starting height
51.75 mm
Delta
-0.02 mm
Latest result
PASS

Disposition: Retain existing bolt / thread

Proof test record Attempt 1 · PASS · Retain existing bolt / thread

Test Attempts

Attempt 1 PASS

Pre-Test Inspection

Acceptable

Acceptable

Yes

Yes

—

—

Fixture Actually Used

—

51.82

Final stack used (specific components)
H52 qty

4

H25 qty

0

H10 qty

0

—

Proof Test

Lubricated

Tap Magic

—

128

No

—

128

Pass

Failure/concern observed

—

—

Disposition

Retain

Note this needs to more fully engage the nuts

—

Machining / Re-Threading

—

—

—

—

—

—

—

—

—

—

—

—

Extension / Prosthesis

—

—

—

—

—

—

—

—

—

—

—

Final Installation

—

—

—

—

—

—

—

—

—

—

—

—

Sign-Off / Traceability

—

—

—

—