⚓ Keel

← Back to diagram

#9

M30 Replace? 5/5 — yes

Nautor comment

Install a bolt extension, a sort of prosthesis that rebuilds the bolt, according to the procedure explained in Appendix 1 at the end of this document.

Bolt dimensions

D2 — Total bolt height
76.14 mm
D1 — Lead to thread
30 mm
H1 — Hull hole depth
33.52 mm
H2 — Keelson to plate
23.23 mm
Plate thickness (calc.)
10.29 mm
Keel width at station
14.5 in

D2 is the bolt's total height, from the head/tip down to the top of the lead. D1 is the height from the lead up to where the threads start. H1 is how deep the hole in the hull is where the bolt sits. H2 is the thickness from the bottom of the keelson to the bottom of the internal plate. Plate thickness is calculated as H1 minus H2. Keel width is measured across the bolt centers at this bolt's station.

Backing plate

Two-hole plate, shared with #8
Height (fore/aft)
80 mm
Width (athwartships)
241.3 mm (9.5 in)
Depth (thickness)
8 mm
Hole diameter
36 mm
Condition
Flat

Proposed extension — profile cutaway · v2 (Nov 12, 2026)

To scale, section through the bolt centreline. Heights in mm above the lead keel baseline. Fiberglass + 8 mm backing plate taken from this bolt's H1. The air gap between the keel and hull faces isn't measurable here (about 0–7 mm); it's drawn at 0, which puts the plate lowest. The design clears the plate either way, and the stud gives full nut engagement up to a 7 mm gap at #8.

Before — #9 as it stands

33.5 (H1) 76.1 tip (D2) 23 in nut #9: Full nut engagement, 19.6 proud M30 nut (23) 8 mm backing plate Fiberglass (25.5) Lead keel (baseline 0)

After — with extension · v2 (Nov 12, 2026)

M30 extension v2 (Nov 12, 2026) 31.5 excavation 23.5 shoulder 54.6 stud 33.5 (H1) 78.1 tip 109.6 total 35mm (10 threads) 5 2 23 Ø50 body 63 plate 75.7 excavation (63 + ½″) Full nut engagement, 21.6 proud Fiberglass hole enlarged to Ø52 up to ~24.5 only — stays clear of the backing plate Tack weld (316 stainless filler) 63×63×6 plate, Ø50.3 hole, top flush with keel Existing M30 bolt, cut to 40 above excavation floor Extension: Ø50 body, M30 female thread Lead keel (baseline 0)

Extension: XM-19 HS, ASTM A479 — MTR required; weld plate 316 stainless, tack welded with 316 stainless filler. M30 nut, 23 mm, seated on the backing plate with no washer (drawn across corners). The original bolt's thread starts at D1. Excavation 75.7 mm square (63 + ½″, the original plate's pocket widened chiselling it out), round the 63 mm plate. Assumed: the fiberglass hole is enlarged to Ø52 (about 1 mm clearance on the Ø50 body).

Strength vs. the A4-70 rod

Rod (M30, A4-70, As 561 mm²): yields at 252 kN, breaks at 392 kN. Each cell is yield / break in kN, with % of the rod's. The stud is the same thread as the rod, so the bar needs at least Rp0.2 450 MPa and Rm 700 MPa.

Section 316 annealed (ASTM A479) 205/515 MPa · weaker than the rod XM-19 annealed (Nitronic 50 / Aquamet 22, A479) 380/690 MPa · weaker than the rod XM-19 high strength (Nitronic 50 HS / Aquamet 22HS) 725/930 MPa · as strong as the rod
Body round the internal thread 258 (102%) / 647 (165%) 478 (189%) / 867 (221%) 911 (361%) / 1,169 (298%)
Shoulder (narrowest) 145 (57%) / 364 (93%) 269 (106%) / 488 (124%) 512 (203%) / 657 (168%)
Stud neck (plain, Ø30) 145 (57%) / 364 (93%) 269 (106%) / 488 (124%) 512 (203%) / 657 (168%)
Stud thread 115 (46%) / 289 (74%) 213 (84%) / 387 (99%) 406 (161%) / 521 (133%)
Internal thread stripping — / 739 (188%) — / 990 (252%) — / 1,334 (340%)
Stud thread stripping in the nut — / 360 (92%) — / 482 (123%) — / 650 (166%)

Bold: the weakest section. The shoulder's tightest fillet radius is 3.6 mm (Kt ≈ 1.8); on the larger unthreaded section that peaks at about 1.4× the thread's nominal stress, below a cut thread root's (Kt about 3–4), so the transition isn't the weak point. The stud thread stops at a 3 mm plain neck at Ø30 and washes out (no undercut); full thread from 31.8 above the keel. Spec minimums, not measured values; thread stripping at 0.6 Rm.

Open print sheet CAD (DXF, M30): extension · weld plate

Machine-shop upload set (M30, qty 2)

Extension: STEP · IGES · STL · Drawing (PDF) · FreeCAD · STEP, threaded · STL, threaded

Weld plate: Cut DXF · STEP · IGES · STL · Drawing (PDF)

Loading 3D model…

Couldn't load the 3D model.

Finished part, threads modelled · drag to rotate

Proof Test / Fixture

Starting proof-test stack — a calculated starting point, not an approved dimension. H1 is remeasured in the field before every test.

Baseline H1
33.52 mm
Calculated starting height
33.58 mm
Delta
0.06 mm
Latest result
PASS

Disposition: Install extension

Proof test record Attempt 1 · PASS · Install extension

Test Attempts

Attempt 1 PASS

Pre-Test Inspection

Acceptable

Corroded

Yes

Yes

—

—

Fixture Actually Used

—

33.3

Final stack used (specific components)
H52 qty

1

H25 qty

0

H10 qty

0

—

Proof Test

Lubricated

Tap Magic

—

254

No

—

254

Pass

Failure/concern observed

—

—

Disposition

Install Extension

—

—

Machining / Re-Threading

—

—

—

—

—

—

—

—

—

—

—

—

Extension / Prosthesis

—

—

—

—

—

—

—

—

—

—

—

Final Installation

—

—

—

—

—

—

—

—

—

—

—

—

Sign-Off / Traceability

—

—

—

—